What is a Paint Can, Pail and Filter Crusher?
A Paint Can, Pail and Filter Crusher crushes paint cans, oil filters, small propane tanks, six-gallon pails and most anything that is small. Some models can handle a wide variety of container types and sizes ranging from pints to 6-gallons. Full cans and pails with lids on are opened, emptied (by EPA Definition) and crushed in twenty seconds or less, and are automatically ejected out the back!
Empty and crush half-pint cans to six-gallon pails in preparation for recycling or disposal. Paints, inks, stains and sealant can be recovered for reuse and the container recycled.
Frequently asked Questions
Who would benefit from a Paint Can, Pail & Filter Crusher?
- Municipalities, Sate / Federal Agencies
- Hazardous Waste Facilities
- Paint Industries
- Automotive Industries
- Production Facilities
- Manufacturing Plants
- Metal Packagers Manufacturers
- Lube Services Facilities
- Aircraft Industry
- Military Aircraft Platforms
- Marine Environments
- Offshore Installations
- Motor Freight and Railroad Transportation
- Oilfield Industry
- Military bases, installation
How much footprint does a Paint Can, Pail & Filter Crusher need?
All Super 6 series crushers are 103″ tall with 35″ of clearance under the stand.
- Super 6M – 37″ W X 37″ D
- Super 6PM – 37″ W X 37″ D
- Super 6PJ – 37″ W X 47″ D
- Super 6PJ-VC – 55” W X 72″D X 107” H
How much does a Paint Can, Pail & Filter Crusher weigh?
- Super 6M – 1600 lbs.
- Super 6PM – 1800 lbs.
- Super 6PJ – 2000 lbs.
- Super 6PJ-VC – 2000 lbs.
How does a Paint Can, Pail & Filter Crusher ship?
Standing up on a flatbed truck
How do you unload a Paint Can, Pail & Filter Crusher from the truck?
A fork-lift is the most used machine for unloading the vertical baler from the shipping truck. The lifting equipment must be designed for lifting the weight of the crusher.
How do you install a Paint Can, Pail & Filter Crusher?
Super 6M:
Tools required are two (2) 9/16-inch wrenches, small clevis, small chain, and a forklift or overhead crane. The machine weighs approximately 900 pounds. You will need approximately 9-1/2 feet of overhead clearance (more is using a forklift) to place the machine on the stand. Dismantle crate and remove all the bolts fastening the machine to the crate. Remove the machine components, including the machine, the stand, and the staging table. The machine is equipped with lifting eye located at the top of the hydraulic cylinder. Attach the crane or forklift to the lift eye using a clevis and chain. Position the stand at the desired location leaving ample room around the machine to allow for machine maintenance. The front of the stand is leveled accordingly. There are leveling bolts at the bottom of stand legs, if necessary, the machine can be leveled. It is recommended that the stand be anchored to the floor using the holes provided in the pads on the legs. These anchor bolts should be 3/8 inch by 4-1/2” long. Once fully assembled an Electrician will need to complete the electrical hookup in accordance with local codes.
HYDRAULIC FLUID
The hydraulic reservoir must be kept full to a level that is visible in the temperature/sight gauge throughout the complete ram cycle. Use a premium grade antiwear hydraulic oil, 150 viscosity grade 32 (mobile #DTE24 or equal). This is the same antiwear hydraulic fluid that is typically used in farm tractor and dump trucks. It should be available at most auto or farm supply stores. Total fluid capacity is approximately 6 US gallons.
OIL FILTER
A medium pressure, high performance 10-micron (absolute) oil filter is standard on all TeeMark Crushers. It should be changed after every 500 hours of operation.
Oil Filter Replacement part # P02-0081
VALVE SETTINGS
All hydraulic and pneumatic valve components have been preset at the factory.
DO NOT RE-ADJUST ANY VALVE SETTINGS WITHOUT FIRST CONSULTING THE MANUFACTURER.
Super 6PM:
Tools required are two (2) 9/16-inch wrenches, small clevis, small chain, and a forklift or overhead crane. The machine weighs approximately 900 pounds. You will need approximately 9-1/2 feet of overhead clearance (more is using a forklift) to place the machine on the stand. Dismantle crate and remove all the bolts fastening the machine to the crate. Remove the machine components, including the machine, the stand, the stand baffle plate, and the staging table. The machine is equipped with lifting eye located at the top of the hydraulic cylinder. Attach the crane or forklift to the lift eye using a clevis and chain. Position the stand at the desired location leaving ample room around the machine to allow for machine maintenance. The front of the stand is leveled accordingly. There are leveling bolts at the bottom of stand legs, if necessary, the machine can be leveled. It is recommended that the stand be anchored to the floor using the holes provided in the pads on the legs. These anchor bolts should be 3/8 inch by 4-1/2” long. The baffle plate fits on top of the stand and between the stand and the machine. Secure the machine to the stand using the 4 – 3/8-16 X 1-1/2” bolts provided. Attach the staging table to the machine using the 2- 3/8-16 X 1” bolts provided.
Once fully assembled an Electrician will need to complete the electrical hookup in accordance with local codes.
HYDRAULIC FLUID
The hydraulic reservoir must be kept full to a level that is visible in the temperature/sight gauge throughout the complete ram cycle. Use a premium grade antiwear hydraulic oil, 150 viscosity grade 32 (mobile #DTE24 or equal). This is the same antiwear hydraulic fluid that is typically used in farm tractor and dump trucks. It should be available at most auto or farm supply stores. Total fluid capacity is approximately 6 US gallons.
OIL FILTER
A medium pressure, high performance 10-micron (absolute) oil filter is standard on all TeeMark Crushers. It should be changed after every 500 hours of operation.
Oil Filter Replacement part # P02-0081
VALVE SETTINGS
All hydraulic and pneumatic valve components have been preset at the factory.
DO NOT RE-ADJUST ANY VALVE SETTINGS WITHOUT FIRST CONSULTING THE MANUFACTURER.
Super 6PJ
Tools required are two (2) 9/16-inch wrenches, two (2) ½ inch wrenches, one 7-16-inch wrench, level, hammer, pry bar, alignment punch, small clevis, small chain, and a forklift or overhead crane. The machine weighs approximately 1800 pounds. You will need approximately 9-1/2 feet of overhead clearance (more if using a forklift) to place the machine on the stand. Dismantle crate and remove all the bolts fastening the machine to the crate. Remove the stand and locate the front of the stand. Position the stand in your desired location leaving ample room around the machine to maneuver the drum jack and drum. Your stand is equipped with leveling bolts; level the stand before continuing. Check you stand height for clearance: if a drum will not fit under the stand, the leveling bolts may be used to raise the stand. It is recommended that the stand be anchored to the floor using the holes provided in the pads on the legs. These anchor bolts should be 3/8 or ½ inch by 4-1/2 inch long. Remove baffle plate from the crate and position it on the top of the stand. This plate will drop down inside, and you will need to check your orientation as the machine is not centered on the stand. The machine is equipped with a lift eye located to the right of the hydraulic cylinder. Attach the crane or forklift to the lift eye using a clevis and chain. Lift machine and locate it with the door facing the front of the stand. An alignment punch will help to align bolt holes as the machine is lowered onto the stand. Once set into place, bolt the machine to the stand using the four 3/8-16×1-1/4-inch bolts and lock washers provided. Attach the staging table to the machine in from of the door using the two 3/8-16×1 inch bolt, nuts and lock washers provided. Once fully assembled an Electrician will need to complete the electrical hookup in accordance with local codes.
AIR REQUIREMENTS
The Super 6PJ uses less than 4 CFM and requires a maximum air pressure of 90 psi. All crushers are equipped with a filter/regulator (part # P01-0105). The pressure of the filter regulator must be set at 90 psi to insure proper machine performance.
HYDRAULIC FLUID
The hydraulic reservoir must be kept full to a level that is visible in the temperature/sight gauge throughout the complete ram cycle. Use a premium grade antiwear hydraulic oil, 150 viscosity grade 32 (mobile #DTE24 or equal). This is the same antiwear hydraulic fluid that is typically used in farm tractor and dump trucks. It should be available at most auto or farm supply stores. Total fluid capacity is approximately 20 US gallons.
OIL FILTER
A medium pressure, high performance 10-micron (absolute) oil filter is standard on all TeeMark Crushers. It should be changed after every 500 hours of operation.
For Machine Serial No. 20714 thru 20772: Part Number P02-0090
For Machine Serial No. 20619 thru 20713: Part Number P02-0088
For Machine Serial No. 20772 and greater; Part Number P02-0088
VALVE SETTINGS
All hydraulic and pneumatic valve components have been preset at the factory.
DO NOT RE-ADJUST ANY VALVE SETTINGS WITHOUT FIRST CONSULTING THE MANUFACTURER.
Super 6PJ-VC:
Tools required are two (2) 9/16-inch wrenches, two (2) ½ inch wrenches, one 7-16-inch wrench, level, hammer, pry bar, alignment punch, small clevis, small chain, and a forklift or overhead crane. The machine weighs approximately 1800 pounds. You will need approximately 9-1/2 feet of overhead clearance (more if using a forklift) to place the machine on the stand. Dismantle crate and remove all the bolts fastening the machine to the crate. Remove the stand and locate the front of the stand. Position the stand in your desired location leaving ample room around the machine to maneuver the drum jack and drum. Your stand is equipped with leveling bolts; level the stand before continuing. Check you stand height for clearance: if a drum will not fit under the stand, the leveling bolts may be used to raise the stand. It is recommended that the stand be anchored to the floor using the holes provided in the pads on the legs. These anchor bolts should be 3/8 or ½ inch by 4-1/2 inch long. Remove baffle plate from the crate and position it on the top of the stand. This plate will drop down inside, and you will need to check your orientation as the machine is not centered on the stand. The machine is equipped with a lift eye located to the right of the hydraulic cylinder. Attach the crane or forklift to the lift eye using a clevis and chain. Lift machine and locate it with the door facing the front of the stand. An alignment punch will help to align bolt holes as the machine is lowered onto the stand. Once set into place, bolt the machine to the stand using the four 3/8-16×1-1/4-inch bolts and lock washers provided. Attach the staging table to the machine in from of the door using the two 3/8-16×1 inch bolt, nuts and lock washers provided.
Attach the vapor bonnet to the bottom of the can ejector chute using the six ¼-20×1 inch bolts, nuts and lock washer provided. From the 5-inch discharge on the blower extend your duct work to the exterior of the building.
Be sure that there is a source of makeup air available to the room or building where the crusher is to be located. Once fully assembled an Electrician will need to complete the electrical hookup in accordance with local codes.
AIR REQUIREMENTS
The Super 6PJ-VC uses less than 4 CFM and requires a maximum air pressure of 90 psi. All crushers are equipped with a filter/regulator (part # T9007521). The pressure of the filter regulator must be set at 90 psi to insure proper machine performance.
HYDRAULIC FLUID
The hydraulic reservoir must be kept full to a level that is visible in the temperature/sight gauge throughout the complete ram cycle. Use a premium grade antiwear hydraulic oil, 150 viscosity grade 46 (medallion plus hydraulic AW46 or equal). This is the same antiwear hydraulic fluid that is typically used in farm tractor and dump trucks. It should be available at most auto or farm supply stores. Total fluid capacity is approximately 20 US gallons.
OIL FILTER
A medium pressure, high performance 10-micron (absolute) oil filter is standard on all TeeMark Crushers. It should be changed after every 500 hours of operation.
For Machine Serial No. 20714 thru 20772: Part Number P02-0090
For Machine Serial No. 20619 thru 20713: Part Number P02-0088
For Machine Serial No. 20772 and greater; Part Number P02-0088
For Machine Serial No. 30000 and greater; Part Number P02-0081
VALVE SETTINGS
All hydraulic and pneumatic valve components have been preset at the factory.
DO NOT RE-ADJUST ANY VALVE SETTINGS WITHOUT FIRST CONSULTING THE MANUFACTURER.
How does a Paint Can, Pail & Filter Crusher work?
Super 6M:
- Position an empty 55-gallon drum under the crusher.
- Use a 55-gallon drum or some type of receiver, to collect the crushed cans.
- Open the crusher door
- Start crusher motor by pulling out the red pushbutton.
- Place a can into the crushing chamber in an upright position with the can opening face down, centered on the crusher grate.
- Close the crusher door and pull both levers on the hydraulic control valve
- When the can is fully crushed, and the hydraulic system has reached full crushing pressure, the first or right-hand lever will disengage, and the hydraulic cylinder will retract.
- When the cycle is complete and the cylinder is fully retracted, the second or left hand lever will disengage.
- The crusher door can now be opened and the crushed can removed. A new can may be placed on the platen and the crushing cycle repeated.
Super 6PM:
- Position an empty 55-gallon drum under the crusher.
- Use a 55-gallon drum or some type of receiver, to collect the crushed cans.
- Open the crusher door
- Start crusher motor by pulling out the red pushbutton.
- Place a can into the crushing chamber in an upright position, centered over the piercer opening on the crusher platen.
- Close the crusher door and pull both levers on the hydraulic control valve
- When the can is fully crushed, and the hydraulic system has reached full crushing pressure, the first- or right-hand lever will disengage, and the hydraulic cylinder will retract.
- When the cycle is complete and the cylinder is fully retracted, the second or left hand lever will disengage.
- The crusher door can now be opened and the crushed can removed. A new can may be placed on the platen and the crushing cycle repeated.
Super 6PJ:
- Position an empty 55-gallon drum under the sealing flange just below the crushing chamber using the drum jack that is supplied with the crusher. Raise the drum until it contacts the sealing flange. DO NOT LIFT THE DRUM PAST THE POINT OF CONTACT WITH THE SEALING FLANGE, THIS COULD CAUSE DAMAGE TO THE CRUSHER.
- Place a second 55-gallon drum below the vapor bonnet, to collect the crushed cans.
- Open the crusher chamber door.
- Begin by pulling out the red emergency stop button.
- Start the crusher by pushing in start button on the control panel.
- Place a can into the crushing chamber in an upright position, centered over the piercer opening.
- Close the crushing chamber door and the crushing cycle will begin automatically. The crushed can will be ejected into the rear drum.
- When the crushing cycle is complete the door will open automatically, and the crusher is ready for the next crushing cycle.
DO NOT ATTEMPT TO OPEN THE DOOR BY HAND. THIS CAN RESULT IN A MALFUNCTION OF THE PNEUMATIC CONTROL SYSTEM.
Super 6PJ-VC:
- Position an empty 55-gallon drum under the sealing flange just below the crushing chamber using the drum jack that is supplied with the crusher. Raise the drum until it contacts the sealing flange. DO NOT LIFT THE DRUM PAST THE POINT OF CONTACT WITH THE SEALING FLANGE, THIS COULD CAUSE DAMAGE TO THE CRUSHER.
- Place a second 55-gallon drum below the vapor bonnet, to collect the crushed cans.
- Begin by pulling out the red e-stop button.
- Start the blower by pushing blower start push button. The blower and the crusher motors are interlocked to prevent the crusher from operating without the blower motor energized.
- Open the crushing chamber door.
- Start crusher motor by pushing the crusher start push button
- Place a can into the crushing chamber in an upright position centered over the piercer opening.
- Close the crushing chamber door and the crushing cycle will begin automatically. The crushed can will be ejected automatically into the rear drum.
- When the crushing cycle is complete the door will open automatically, and the crusher is ready for the next crushing cycle.
DO NOT ATTEMPT TO OPEN THE DOOR BY HAND. THIS CAN RESULT IN A MALFUNCTION OF THE PNEUMATIC CONTROL SYSTEM.
Electrical options for a Paint Can, Pail & Filter Crusher
Super 6M – 1-1/2 HP, 230V, SINGLE PHASE, 10A
Super 6PM – 1-1/2 HP, 230V, SINGLE PHASE, 10A
Super 6PJ – 1-1/2 HP, 230V, SINGLE PHASE, 10A
Super 6PJ-VC –1-1/2 HP, 230V, SINGLE PHASE, 10A w/Starter
Hydraulic oil for a Paint Can, Pail & Filter Crusher
Super 6M – Use a premium grade antiwear hydraulic oil, 150 viscosity grade 32 (mobile #DTE24 or equal). Total fluid capacity is approximately 6 US gallons
Super 6PM – Use a premium grade antiwear hydraulic oil, 150 viscosity grade 32 (mobile #DTE24 or equal). Total fluid capacity is approximately 6 US gallons.
Super 6PJ – Use a premium grade antiwear hydraulic oil, 150 viscosity grade 32 (mobile #DTE24 or equal). Total fluid capacity is approximately 20 US gallons.
Super 6PJ-VC – Use a premium grade antiwear hydraulic oil, 150 viscosity grade 46 (medallion plus hydraulic AW46 or equal). Total fluid capacity is approximately 20 US gallons.
Safety Systems may include:
The Super 6 M is equipped with a safety interlock system that is linked to the crushing chamber door. The interlock system prevents operator injury by stopping all functions of the machine in the event that the crushing chamber door is opened during the crushing process. The explosion proof motors, motor controls, and connections on your crusher are UL listed and CSA certified for Class 1, Group D, Hazardous locations. It is up to the purchaser to have the final connections made by a licensed electrical contractor in compliance with the appropriate local and national electrical codes.
The Super 6PM is equipped with a safety interlock system that is linked to the crushing chamber door. The interlock system prevents operator injury by stopping all functions of the machine in the event that the crushing chamber door is opened during the crushing process. The explosion proof motors, motor controls, and connections on your crusher are UL listed and CSA certified for Class 1, Group D, Hazardous locations. It is up to the purchaser to have the final connections made by a licensed electrical contractor in compliance with the appropriate local and national electrical codes.
The Super 6PJ is equipped with a safety interlock system that is linked to the crushing chamber door. The interlock system prevents operator injury by stopping all functions of the machine in the event that the crushing chamber door is opened during the crushing process. The explosion proof motors, motor controls, and connections on your crusher are UL listed and CSA certified for Class 1, Group D, Hazardous locations. It is up to the purchaser to have the final connections made by a licensed electrical contractor in compliance with the appropriate local and national electrical codes.
The explosion proof motors, motor controls, and connections on your crusher are UL listed and CSA certified for Class 1, Group D, Hazardous locations. It is up to the purchaser to have the final connections made by a licensed electrical contractor in compliance with the appropriate local and national electrical codes.
The Super 6PJ-VC is designed to vent VOCs and propellant from the crushing chamber and the collection drum. A 24×24 bag filter (part #P04-0045) housed within the filtration cabinet filters particulates from the air stream. The Super 6PJ-VC will provide 250-350 CFM of particulate free air to be handled in accordance with local regulations.
The explosion proof motors, motor controls, and connections on your crusher are UL listed and CSA certified for Class 1, Group D, Hazardous locations. It is up to the purchaser to have the final connections made by a licensed electrical contractor in compliance with the appropriate local and national electrical codes.
Preventative Maintenance for a Paint Can, Pail & Filter Crusher
RECOMMENDED PERIODIC MAINTENANCE
- Change the hydraulic oil filter element every 500 hours; more often if your system is in an extremely dirty atmosphere.
- Change the hydraulic oil completely every 5000 hours or 5 years of operation, whichever comes first.
- Remember your machine is only as good as your maintenance.
Available options for a Paint Can, Pail & Filter Crusher
Super 6M
- Vapor Control
- Carbon Filtration
- 5hp, 208-230/460v, 3ph, 5A
Super 6PM
- Vapor Control
- Carbon Filtration
- Mega Piercer
- 5 HP, 208-230/460V, 3 Phase, 11-10/5A
Super 6PJ
- Vapor Control
- Carbon Filtration
- Mega Piercer
- 5 HP, 208-230/460V, 3 Phase, 11-10/5A
Super 6PJ-VC
- Power System: 5hp 208-230/460v 3ph, 13.2/6.5a, 15 second cycle time
- Collection System: 1hp, 230/460v, 3ph 3.7/1.8 amp
- Carbon Package
The TeeMark Super 6M Crusher can crush 1/2 Pint to 6 Gallon Containers in twenty seconds or less. This machine can crush six-gallon pails and most anything that is small. Oil filters small propane tanks and a variety of pails and cans are all crushed by the Super 6M. When crushing one container per cycle, the Super 6M can crush up to 150 containers per hour. This Crusher excels at crushing small propane tanks.
